A snowblower belt usually needs to be changed every one to three years, depending on the model and how often it is used. To change a snowblower belt, first, turn off the engine and disconnect the spark plug. Then remove the gas tank and engine cover. Next, locate the tensioner pulley and release the tension on the belt. Finally, remove the old belt and install the new one. Follow these steps to properly change a simple snowblower belt.
- Turn off the engine and disconnect the spark plug. This will prevent the snowblower from accidentally starting while you are working on it.
- Remove the gas tank and engine cover. These parts will need to be removed in order to access the belt.
- Locate the tensioner pulley and release the tension on the belt. The tensioner pulley is usually located near the engine.
- Remove the old belt and install the new one. Make sure that the new belt is installed correctly and that it is tight enough.
- Replace the gas tank and engine cover. Be sure to reconnect the spark plug before starting the snowblower.
Changing a snowblower belt is a relatively simple task that can be done by most people. However, if you are unsure of how to properly change a snowblower belt, it is always best to consult with a professional.
How to Change belt in Single-Stage Snow Blowers?
If your snow blower is starting to make noise or isn’t running as smoothly as it used to, it might be time to change the belt. This is a pretty easy process on most single-stage snow blowers and only takes a few minutes. Here’s how to do it:
- Disconnect the spark plug wire from the spark plug so the snow blower can’t accidentally start while you’re working on it.
- Remove the housing cover from the top of the snow blower (this will give you access to the belt).
- Use a socket wrench to loosen the bolt that holds the auger pulley in place.
- Slide the old belt off of the pulleys and dispose of it.
- Put the new belt on, making sure it’s routed correctly through all the pulleys.
- Tighten the bolt on the auger pulley and replace the housing cover.
- Reconnect the spark plug wire and you’re done!
How to Change belt in Two-Stage Snow Blowers?
If you need to change the belt on your two-stage snow blower, follow these steps:
- Park the snow blower on a level surface and turn off the engine.
- Remove the spark plug wire from the spark plug.
- Disengage the auger by moving the lever to the “disengaged” position.
- Remove the skid plate, if applicable.
- Locate the idler pulley near the auger housing. The idler pulley is typically a spring-loaded pulley that keeps tension on the belt.
- Depress the idler pulley to release the tension on the belt and slip the belt off of the pulley.
- Slip the new belt onto the idler pulley and release the pulley to tension the belt.
- Replace the skid plate and spark plug wire.
- Start the engine and engaged the auger to test the new belt.
How to Change belt in Three-Stage Snow Blowers?
If you have a three-stage snow blower, chances are that you’ll eventually need to change the belt. This is a relatively easy process, but there are a few things you’ll need to keep in mind. Here’s a quick guide on how to change the belt in three-stage snow blowers.
- First, make sure that the snow blower is turned off and unplugged. You don’t want to accidentally turn it on while you’re working on it.
- Next, remove the auger housing cover. This will give you access to the belts.
- Take a look at the belts and see how they’re routed. Make a note of this so you can put the new belts on the same way.
- Now, remove the old belts. You may need to use a pair of pliers to get them started.
- Install the new belts, making sure that they’re routed correctly.
- Finally, replace the auger housing cover and you’re done!
How to Change belt in Electric Snow Blowers?
If your electric snow blower has stopped working, it may be because the belt has come off. Fortunately, this is an easy problem to fix. Just follow these steps:
- Unplug the snow blower from the power outlet.
- Lift up the cover on the front of the machine. This will expose the belt.
- Use a pair of pliers to remove the old belt from the pulleys.
- Put the new belt around the pulleys and thread it through the slots in the cover.
- Replace the cover and plug in the snow blower. It should now be working properly.
How to Change belt in Gas Snow Blowers?
If the belt on your gas snow blower is worn, damaged, or broken, it will need to be replaced. Fortunately, this is a relatively easy repair that you can do yourself. This guide will walk you through the steps of how to change the belt in a gas snow blower.
- Disconnect the spark plug wire from the spark plug. This will prevent the snow blower from accidentally starting while you are working on it.
- Remove the cover from the engine by unscrewing the bolts that hold it in place.
- Locate the belt that needs to be replaced and remove it from the pulleys.
- Install the new belt onto the pulleys and make sure that it is seated correctly.
- Replace the engine cover and screw it in place.
- Reconnect the spark plug wire to the spark plug.
Your gas snow blower is now ready to use!
Final Words:
Snow blowers are a great way to keep your driveway and walkways clear during the winter months. But like any other piece of equipment, they require regular maintenance to keep them running properly. One of the most common maintenance tasks is changing the belt. With a little bit of know-how, you can easily change the belt on your snow blower yourself. Just follow the steps in this guide and you’ll have your snow blower up and running in no time.
